Raychem QuickStat Installationshandbuch PDF herunterladen (Seite 1)

Description

The QuickNet-RK repair kit is for repairing heating cable that is damaged

during installation of the QuickNet mat. The kit includes jumper wires to

bridge the heating element after the damaged section is removed. The kit

contents are sufficient to repair one damaged section up to 5 inches long. If

more than 5 inches of cable has been damaged, the mat must be replaced.

Tools Required

• Wire Strippers 16-26 AWG • Heat gun (1000˚F air temp

• Gloves with heat deflector required)

• Scissors • Multimeter (capable of 200K ohms)

Other Required Materials

• QuickNet System Installation Manual (H57704)

• QuickStat Thermostat Installation and Operation Manual (H57725)

Optional Tile Removal Tools

• Grout removal tool • Hammer

Approvals

Radiant Floor HeatingRadiant Floor Heating

WARNING: Shock and Fire Hazard.

If the QuickNet mat is damaged or not installed

properly, fire or shock could occur resulting in

serious personal injuries or damage to property. You

must carefully follow the warnings and instructions

contained in these instructions and the QuickNet

Installation Manual (H57704). Contact Tyco Thermal

Controls for assistance.

• The QuickStat thermostat must be used. It has a

ground-fault circuit interrupter (GFCI) to prevent

electric shock.

• The QuickNet-RK repair kit must be installed

by qualified personnel familiar with generally

accepted construction techniques and safe electrical

practices. The installation must comply with all

national and local electrical codes. If you are

unfamiliar with these requirements, contact a

licensed electrician.

• Electric wiring and the heating mat are installed

in the floor. Be sure that the floor is not penetrated

by nails, screws, or similar devices that can cause

damage on first installation or during subsequent

floor repairs in the future.

• Do not use this Repair Kit to splice different QuickNet

mats together. It is designed only to repair a damaged

section of heating cable in a single mat.

• The QuickNet heating cable cannot be cut to length,

crossed over itself, or installed closer than the

spacing in the mat.

• QuickNet mats can only be installed beneath ceramic

tile or natural stone surfaces. Do not install beneath

wooden, carpeted, linoleum, or other type floors.

• Do not step directly on or damage the heating cable

during installation.

• Do not install the QuickNet mat across expansion

joints.

• Follow the manufacturer’s instructions for installing

tiles, scratch coat, thin-set mortar, or quick drying

mortar beds.

• Do not allow heating cable, cold lead, or floor

temperature sensor to cross over themselves or

each other.

Installation Instructions

QuickNet-RK

QuickNet

™

Heating Cable Repair Kit

Kit Contents:

Item Qty Description

A 2 Jumper wires (blue)

B 6 SolderSleeve

connectors

C 4 Heat-shrinkable tubing

D 1 Ground wire (non-insulated)

The QuickNet-RK Repair Kit is for making minor repairs

to the QuickNet heating cable if it is damaged during or

after installation. Because the condition of the damaged

mat, site conditions and installer capability can vary,

Tyco Thermal Controls does not warrant the repair or

warrant that the repaired floor warming system will

function properly. Use of this kit voids the warranty

of the repaired portion of the heating cable. Repairs

should only be attempted by a qualified electrician or

experienced craftsmen familiar with good electrical

practice and techniques for tile installation and removal.

Contact Tyco Thermal Controls for assistance.

WARRANTY & APPROVALS DISCLAIMER

WARNING:

INSTALLATION GUIDELINES:

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - QuickNet-RK

DescriptionThe QuickNet-RK repair kit is for repairing heating cable that is damaged during installation of the QuickNet mat. The kit includes jumper

Seite 2 - 240/(120)VAC

QuickNet-RK Installation Instructions213 45• Turn off the power to the QuickNet floor warming system at the circuit breaker before starting any repa

Seite 3

QuickNet-RK Installation Instructions37• Remove sufficient mortar to expose 4-5 inches of heating cable on either side of the damage. Using scissors

Seite 4

QuickNet-RK Installation Instructions4• Twist two ground wires together.• Heat only 1/2" of the insulated ends of the heating elements to soft

Seite 5

QuickNet-RK Installation Instructions5• Strip 1/2" of insulation off both ends of each jumper wire.• Slide SolderSleeve connector onto one hea

Seite 6 - 1/2"

QuickNet-RK Installation Instructions6• Cut ground jumper to length, allowing 1/2" overlap on each end of twisted grounding wire.• Slide Solde

Seite 7 - Testing Procedure

QuickNet-RK Installation Instructions7 This test ensures that the insulating jackets of the mat are not damaged. A low value indicates the mat has be

Seite 8 - Project data

Weitere Dokumente für Thermostate Raychem QuickStat

Um das Dokument anzuzeigen Raychem QuickStat Installationshandbuch

Raychem QuickStat Installationshandbuch (12 Seiten)

Raychem QuickStat Installationshandbuch (6 Seiten)

Um das Dokument anzuzeigen Raychem QuickStat Bedienungsanleitung

Raychem QuickStat Bedienungsanleitung (13 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Raychem QuickStat Installationshandbuch Seite 1

Stöbern Sie online oder laden Sie Installationshandbuch nach Thermostate Raychem QuickStat herunter. Raychem QuickStat Installation manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Thermostate Raychem QuickStat

Kommentare zu diesen Handbüchern

Raychem QuickStat Installationshandbuch Seite 1

Stöbern Sie online oder laden Sie Installationshandbuch nach Thermostate Raychem QuickStat herunter. Raychem QuickStat Installation manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Thermostate Raychem QuickStat

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermostate Raychem QuickStat